Showing posts with label garden. Show all posts
Showing posts with label garden. Show all posts

Sunday, May 17, 2015

DIY Worm Composting Bin

Lately, everyone has been talking about ways to Go Green. Making your own worm composting bin is a cheap, easy, and fun way to Go Green! Not only does it decrease the amount of waste you need to throw away, but it results in amazing nutrient-rich organic fertilizer for your garden, flowers, lawn, or even your house plants.

You can buy fancy bins at your local hardware store, or from multiple places on-line. Or you can save a bunch of money and make your own!

Needed Materials:
2 Rubbermaid-type containers
Drill
Small Blocks of wood or rocks
Newspaper
Cardboard
Food Scraps
Dirt
Red Wriggler Worms




Step 1: Drill the Drainage holes.
Drill small holes in the bottom of one of your bins. This is going to be the bin that the worms will be in, so you don't want to make the holes too large. I used a 1/8" drill bit. The purpose of these holes is to provide drainage. Most of the time, there will be little or no drainage. But if you feed them something like watermelon, you are going to need the drainage holes. Place the holes on the lowest part of your bin, since that is where the liquid would be most likely to pool.


Step 2: Drill the ventilation holes.
Drill larger holes near the top edge of the same bin that you drilled the drainage holes. Keep in mind that this bin is going to be placed inside the other bin. Make sure the holes are near the top, so they won't be covered by the other bin. I used a 1/2" drill bit. If you don't have a large drill bit, just drill many small holes. Don't worry, as long as you provide a healthy environment for your worms, they are not going to escape out of these holes. If you are worried, you could cover these holes with a fine mesh.

Step 3: Place your spacers.
Put some scrap blocks of wood or some rocks inside the outer bin. This is the bin without the holes. The purpose of these is to hold the inner bin up a little for the drainage. If you don't have scrap wood pieces or rocks, just look around for something around your house that will elevate the inner bin a couple inches.

Step 4: Insert your inner bin into the outer bin.


Step 5: Rip up some newspaper and lay it on the bottom. 
I like to rip it into squarish pieces, but you may like to use strips. Whatever you like is fine, this is going to provide the bedding. Be sure to only use the normal newspaper pages. Do not use the shiny ad pages of the newspaper. The inks that they use for those can be toxic to the worms.


Step 6: Cut up some cardboard and add it to the bedding. 
Again, you want to use normal cardboard. Do not use any that is coated in that shiny stuff and be sure that any area that was taped or had a sticker on it is not used. The glues in the stickers and tapes can also be harmful.


Step 7: Moisten the bedding.
I forgot to take a picture of this step, but wet your newspaper and cardboard. It should be wet, but you should not be able to squeeze any water out of it.

Step 8: Get your worms ready.
I ordered my worms from Uncle Jim's Worm Farm. I had bought from them before and they also have a live guarantee, but I know there are several other suppliers out there.

I received my worms within 3 days, but I was a little worried when I saw the package. I don't know what the post office did, but the box was completely smashed.



Luckily, my worms seemed alright. I opened them up as soon as I got them and gave them a good watering. They were pretty dry from shipping. Within an hour of getting some water, they started to perk up.

Step 9: Add your food scraps, dirt, and worms.
Worms do not have teeth, so they eat dirt to aid in their digestion. Worms will eat most fruit and vegetable scraps. Things like apple cores, watermelon rinds, potato peelings, and banana peels are good, but try to limit or avoid feeding them citrus fruits, onion or garlic. If you feed them something that has seeds, like pumpkin, they will eat it but they do not digest the seeds. So you will find seeds when it comes time to harvest the compost. They also like to eat coffee grounds, tea bags, breads, egg shells, pet hair, and even dryer lint. If you use a liquid fabric softener, do not feed them your dryer lint. Do not feed them any dairy, oils, salty foods, or meats.


Step 10: Cover the entire pile with wet newspaper, packing paper, or cardboard. 
This helps to keep everything moist and also helps to darken it. Worms do not like light, so the darker the better for them. Try to store your bin either in a darker area inside your house or a shady area outside. I keep mine in my basement. Ideally, you want them to stay around 60-75 degrees F. If they get too cold or too hot, they will die.


Step 11: Continue to feed your worms, as you have food scraps to feed them.
Remember to also continue to provide them with things like newspaper and to keep everything moist. The amount that you feed them, really depends on many factors. They can generally consume about half their body weight a day. But what they are eating, how warm it is and how moist it is all come into play. Also, they are going to reproduce, so you can't really know the exact weight of your worms at any given time.

Step 12: Harvest your vermicompost.
Your worms will consume your table scraps and turn them into a very dense, nutrient-rich organic fertilizer. An easy way to harvest without picking through the worms is to feed on only one end of the bin. When you want to harvest that side, just start feeding on the other end of the bin. The worms will move to the food. Then you can easily scoop out the vermicompost.


Step 13: Add your vermicompost to your garden, yard, or even mix it with water to make worm tea and use it to water your houseplants. You will have amazing results!

Monday, May 26, 2014

Make a Bird Feeder for Under $2

I have been trying to attract more birds. I built and put up some more birdhouses, added a bird bath, and wanted to add some more feeders. I found this quick and easy plan on Ana White's website.

This plan uses just one 6 foot cedar fence picket and took me less than an hour to build. I bought my picket from Menards when it was on sale for $1.18. That's not a bad price for a bird feeder!

For more details about the plan, please visit Ana White's website, but here are the steps that I took to build mine.

Needed Supplies:
6' cedar picket at 5 1/2" wide. The thickness may vary from board to board. (My plan is based off a 5/8" thickness.)
Drill
Saw (I used my miter saw, but any kind of saw that you have will work.)
1 1/4" nails, suitable for exterior use.
Wood glue, suitable for exterior use.
Screw Eye or Post



Step 1: Using a 6' x 5 1/2" cedar picket, cut the following pieces:

1 at 7" (bottom)
2 at 7 3/4" cut one end to a gable point at 45 degrees. (sides)
2 at 10" (roof)


Step 2: Connect the bottom to the sides. I first used wood glue for the initial connection. Then I pre-drilled nail holes and used galvanized 3D 1 1/4" nails that I had left over from another project. If you are going for looks, you may want to use stainless steel finishing nails.


Step 3: Measure the thickness of your board. Cut the thickness of your board off one of the roof board edges. My board was 5/8" thick, so I cut 5/8" off of one board so it measured 10" x 4 7/8".

Step 4: Connect the shorter roof to the sides. Again, I used wood glue and the 1 1/4" nails.


Step 5: Connect the longer roof to the sides and the top of the other roof.


Step 6: Measure the length from the outer edge of the side to the outer edge of the other side. This should be the length of the bottom plus the width of the two boards. In my case, it was 7" + 5/8" + 5/8" = 8 1/4".

Step 7: Cut the cedar picket at the length that you just measured. Then cut two 1 1/2" widths out of this board. You will have 2 pieces at 8 1/4" x 1 1/2" (side rails). You can discard the leftover piece.

Step 8: Connect the side rails to the bottom and the sides.


Step 9: Attach a screw eye if you want to hang it. If you prefer, you could attach it to the top of a post.


Step 10: Add bird food and wait for the birds to come.


This plan does not use the entire 6 foot picket. I had about 20" left. If you wanted to, you could make the feeder larger by extending the length and/or increasing the height. I would not make it much higher, as this feeder is open on the sides and the shorter height prevents too much precipitation from getting into the feeder.

This fast and easy plan would be a great project for kids to do and it is just in time for Father's Day!








Monday, May 12, 2014

Make a Birdhouse for under $1

I wanted to build some quick bird houses. I found this pattern on Ana White's Website. This pattern uses just one cedar fence picket to make two birdhouses. I bought a couple cedar fence pickets at Menards. The pickets were on sale for $1.18. That means only $.59 a birdhouse!

The project plan on Ana White's website is very detailed, but here are the steps that I took to make mine.

Needed Supplies:
6' cedar picket at 5 1/2" wide and 1/2" thick. (this will make 2 houses)
1 1/4" nails and screws, suitable for exterior use.
Wood glue, suitable for exterior use.

Step 1: Using a 5 1/2 inch wide x 6 foot cedar picket, cut the following pieces.
1 at 5 1/2" x 8 1/2"  (back)
2 at 5 1/2" x 5 1/2"  (top and bottom)
1 at 5 1/2" x 5"  (front)
2 at 5 1/2" x 4 3/4"  (sides)

Step 2: Connect the sides to the front. I used wood glue to initially connect them.

Step 3: I then used 1 1/4" nails to attach the sides to the front.

Step 4: Attach the back to the bottom.

Step 5: Attach the front and sides to the bottom.

Step 6: Attach the back to the sides.

Step 7: Attach the top to the sides. I used 1 1/4" screws for this step. When the birdhouse needs cleaning, I can easily remove the top using the screws.


Step 8: Drill a hole in the house. If you chose to add a perch you can, I chose not to add one to prevent any predators from trying to enter the house.

I made two birdhouses. Now, I just need to attach them to a tree or a post and wait for the birds to move in.










Sunday, January 12, 2014

Little E's Garden Bench


I haven't been sleeping much lately, so I had to come up with a project. My youngest niece's 3rd birthday is in March. It's a long ways away, but I found a great build for her!

I am slightly obsessed with Ana White's website. I saw this cute plan ana-white.com/2013/08/plans/childs-bench-arbor and I knew it would be perfect!


I still have to fill in the screw holes and I need to sand the entire thing to soften up the curves. Then I have to deal with the painting. I love the building part of these projects, but I hate the finishing part.

Here are a few pictures of the build. Yes, I had to build it in my living room. My basement is not heated and it has been super cold out, so I did most of the building in my living room. Just ignore all the sawdust and wood chips all over the floor.

I'll have to add pictures once it's really completed, but that won't be for awhile because it is way too cold to paint in the basement right now. Here it is for now.

Side Trellis
Bench
Sides and Bench Together
Making the Arch
Arbor Completed
Back of the Bench
Oliver Trying it Out