Pages

Tuesday, November 4, 2014

DIY Pottery Barn Valencia Armoire Knock-off Full Material and Cut Lists

I built myself a new bedroom set. The bedroom set included a Pottery Barn Hudson Bed knock-off, a nightstand, a large wooden dog bed, and a Pottery Barn Valencia Armoire knock-off. I built the armoire in two sections. You can find the detailed steps for the dresser portion of the armoire here and the detailed steps of the shelving unit portion of the armoire here. Today, I will give you complete material and cut lists to build the entire armoire.

Pottery Barn's Valencia Armoire sells for $1,599. I made mine for under $250!








Because I have a small bedroom, I did decrease the depth of the drawers and shelves by about 4". If you want to build your armoire to the Pottery Barn specifications, you will need to increase the depth. If you have a smaller area, you could also decrease the depth.

Here is a complete material list if you would like to build this armoire. Depending upon the cost of the hardware, you could build this entire armoire for under $250!

Needed materials:
3 - 1"x2" at 8 feet
1 - 1"x4" at 4 feet
1 - 1"x10" at 3 feet
2 - 1"x10" at 8 feet
1 - 1"x12" at 8 feet
4 - 2"x2" at 8 feet
1 - 4"x4" at 4 feet
1 - 1/4" plywood at 4'x8'
1 - 1/4" plywood at 4'x4'
1 - 1/2" plywood at 4'x4'
2 - 3/4" plywood at 4'x8'
1 1/4" PH screws
2 1/2" PH screws
1 1/4" finishing nails
3/4" finishing nails
1 1/4" wood screws
2 - 16" Bottom Mount Euro drawer slides
4 drawer pulls
2 cabinet pulls
6 hinges
2 magnetic latches
Brackets (to hold together the two portions)

Here is the complete cut list if you want to build both parts of the armoire.

2 - 1/4" plywood at 16" x 37 1/2" (drawer bottoms)
1 - 1/4" plywood at 26 3/4" x 41 1/2"(dresser back)
1 - 1/4" plywood at 40 3/4" x 41 1/2"(shelving unit back)
2 - 1/2" plywood at 19 1/8" x 37" (doors)
2 - 3/4" plywood at 15 3/4" x 26 3/4" (dresser sides)
3 - 3/4" plywood at 18" x 40" (shelves)
2 - 3/4" plywood at 18" x 40 3/4" (shelving unit sides)
1 - 3/4" plywood at 20" x 42 1/2" (dresser top)
1 - 3/4" plywood at 21 1/2" x 45 1/2" (shelving unit topper)
4 - 1"x2" at 15 3/4" drawer slide holders)
2 - 1"x2" at 38 1/2" (drawer divider and back middle frame)
2 - 1"x2" at 40 3/4" (shelving unit side trim)
1 - 1"x4" at 38 1/2" (shelving unit header)
4 - 1"x10" at 36" (drawer fronts and backs)
4 - 1"x10" at 16" (drawer sides)
2 - 1"x12" at 38 1/4" (drawer faces)
4 - 2"x2" at 26 3/4" (dresser sides of frames)
4 - 2"x2" at 38 1/2" (dresser top and bottom of frames)
2 - 2"x2" at 40" (shelving unit top frames)
2 - 4"x4" at 3" (back feet)
2 - 4"x4" at 3" then cut at a 15 degree bevel (front feet)

Enjoy your new armoire and be sure to check out the other items that I built in my new bedroom set!



No comments:

Post a Comment